美孚抗燃液压油派路特HFD46

Mobil Pyrotec HFD 46Fire-Resistant Hydraulic FluidProduct DescriptionMobil Pyrotec HFD 46 is a high performance fire resistant hydraulic fluid. It is designed for use in electro-hydraulic governor con

  • 型号: 美孚抗燃液压油派路特HFD46

Mobil Pyrotec HFD 46

Fire-Resistant Hydraulic Fluid

Product Description

Mobil Pyrotec HFD 46 is a high performance fire resistant hydraulic fluid. It is designed for use in electro-hydraulic governor control systems of steam turbines, including systems using fine tolerance servo valves. It is also recommended as a fire resistant lubricant in, for example, steam and gas turbines as well as fire resistant hydraulic systems. Mobil Pyrotec HFD 46 is approved by Factory Mutual Insurance Company.

Mobil Pyrotec HFD 46 is formulated to provide good oxidation stability. Physical properties such as foaming, air release and demulsibility are controlled to meet the limits specified by turbine manufacturers.

Mobil Pyrotec HFD 46 has been evaluated in stringent tests for fire resistance. It will burn if the bulk fluid temperature reaches 368ºC and is exposed to an open flame.  However, in the spray ignition hot manifold ignition test (Factory Mutual Standard 6930 AMS 3150C) there is no flashing or burning at 704ºC.

 

Features and Benefits

Mobil Pyrotec HFD 46 has the following benefits:

  • Inherent resistance to fire hazards

  • Long component life due to excellent anti-wear properties

  • Long fluid life due to high oxidation resistance

  • Factory Mutual approval

 

Applications

Mobil Pyrotec HFD 46 is recommended for use in:

- Electro-hydraulic governor control systems of steam turbines, especially where a high performance fluid is required
- Hydraulic and oil circulation systems operating in conditions subject to fire hazards

Mobil Pyrotec HFD 46 is unsuitable for:

- Hydraulic systems subjected to low temperatures. The normal operating temperature should normally be up to 65ºC to minimize thermal degradation. However, it is possible to operate with fluid temperatures up to a maximum of 150ºC.
- Use with Neoprene, nitrile and silicone rubber materials. Mobil Pyrotec HFD 46 is compatible with seal and hose materials such as butyl rubber and Viton.
- Use with petroleum oils, conventional soluble emulsions, water in oil emulsions or water glycol fluids. ExxonMobil will be pleased to give advice on flushing procedures.
- Use on most paints (other than two part epoxy paints), enamels and varnishes. Because of the solvent properties of Mobil Pyrotec HFD 46, it is necessary, therefore, to consider treating all internal surfaces likely to come in o contact with it.

 

Specifications and Approvals


Mobil Pyrotec HFD 46 meets or exceeds the requirements of: 
Factory Mutual Standard 6930 AMS 3150CX


 

Typical Properties


Mobil Pyrotec HFD 46 
ISO Viscosity Grade46
Viscosity, ASTM D 445, cSt @ 40ºC43.4
Viscosity, ASTM D 445, cSt @ 100ºC5.0
Pour Point, ºC, ASTM D 97 (max)-20.0
Flash Point, ºC, ASTM D 92 (min)246.0
Color, VisualColorless


 

Health and Safety

Based on available information, this product is not expected to produce adverse effects on health when used for the intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDS's are available upon request through your sales contract office, or via the Internet. This product should not be used for purposes other than its intended use. If disposing of used product, take care to protect the environment.


电话咨询
产品中心
核心技术
QQ客服